Roof Replacement & Re-Roofing in Burswood

A roof restoration renews a tired but sound Burswood roof for a fraction of replacement: we treat the moss and lichen, high-pressure clean, replace broken tiles, re-bed and re-point the ridge caps in a flexible compound, then seal and coat with a Dulux AcraTex membrane as accredited applicators.

It’s the right call when the tiles have decades left but the surface and pointing are gone — the same judgement we bring to nearby Victoria Park. We’ll tell you honestly whether a restoration suits your roof or whether repairs or a re-roof make more sense, and the finished job carries both a manufacturer coating warranty and our 10-year workmanship warranty. Most Burswood homes take two to three days depending on the repairs needed before coating. As accredited applicators we prepare to the manufacturer’s specification, so the membrane actually holds — a coating only lasts if the surface beneath it was treated, cleaned and repaired properly first, which is exactly where a cheap spray-over fails within a couple of summers.

Most Burswood roof problems come down to a handful of failures: cracked or slipped tiles, perished ridge pointing, rusted valley irons and tired flashings. We trace the leak to its actual source — which is rarely under the ceiling stain — and fix the cause, whether that’s replacing matching tiles, re-bedding and re-pointing the ridge in a flexible compound, or renewing a corroded valley.

We’ll always tell you honestly when a roof is genuinely repairable versus when the repairs are mounting up and a restoration would serve you better, as it often does through nearby Lathlain. Prompt repair matters: a single cracked tile left through a wet winter becomes soaked insulation, stained ceilings and, eventually, damaged roof timber. Every repair is backed by our workmanship warranty, and because we photograph what we find and talk you through it, you’ll understand exactly what was wrong and what we did about it rather than being handed a bill and a shrug.

Roof carpentry is the structural timber under your tiles — the rafters, battens and trusses that hold everything up. On Burswood homes we repair and rebuild that framing to standard: sistering weakened members, replacing rotted or termite-damaged timber, and reinstating trusses that have been cut for a skylight, duct or downlight.

We also test for delignification, the chemical breakdown that leaves roof timber looking sound but unable to hold a fixing — the same treatment we carry out through nearby Carlisle where the timber is worth saving rather than replacing. As registered builders we can certify structural carpentry, which a general handyman can’t, and we assess the whole load path while we’re in the roof space so a repair addresses the cause, not just the symptom. Where a member is load-bearing we prop it safely with acrow props and work to a structural engineer’s design before anything is cut — it’s the natural companion to our tie-down and structural-defect work.

A roof inspection is the cheapest way to know exactly what your Burswood roof needs before you commit to anything — or before you buy. We get onto the roof and into the roof space, physically checking the tiles, pointing, valleys, flashings, gutters and the structural timber, then hand back a clear written report with photographs.

On older homes we test the timber for rot, termite damage and delignification; on newer ones we look for the builder-grade detailing faults that leak early. It’s the same thorough check we run through nearby East Victoria Park, and it’s what tells you whether a roof needs a minor repair, a restoration or something structural. If you’re buying a home, an inspection of the one part most people skip — the roof space — is money very well spent, and the written report gives you something concrete to put in front of an agent, a buyer or your insurer rather than a verbal all-clear.

When a storm hits a Burswood roof — lifting ridge caps, cracking tiles or dropping a limb through it — our first job is always to make the roof safe: tarp the opening, stop the water, and take the immediate danger out of it. Only then do we scope the permanent repair and deal with your insurer.

We document the damage thoroughly, separating genuine storm damage from pre-existing wear so the claim is properly supported, and we check the framing around any impact because a limb strike shock-loads more than the visible hole. It’s the same rapid response we bring to nearby Rivervale. Getting there quickly limits the internal damage — an hour of water ingress can mean ceilings and insulation you’ll otherwise be replacing later. We liaise with your insurer directly and hand back a documented, photographed scope, so the claim is straightforward and the repair holds up in the next blow rather than becoming the next emergency.

A roof tie-down is the continuous chain of connections that holds the roof down to the walls and the walls to the footings, resisting the wind trying to lift the roof off. On Burswood homes we assess that load path against the site’s wind classification, then reinforce it with framing anchors, triple-grips and proper anchorage wherever it falls short.

The single most important point is the re-roof: converting a tile roof to lightweight Colorbond removes dead weight and raises the net uplift, so the tie-down must be reassessed — exactly as we do through nearby Victoria Park. As registered builders we can certify the structural work, and we work to the wind and framing standards by name rather than guesswork. On exposed or elevated blocks we design to the wind actions in AS/NZS 1170.2 rather than a generic detail, so the roof stays put when the weather turns — it’s the natural companion to structural-defect rectification.