Pressure Cleaning in Stratton

Roof cleaning strips the moss, lichen and black weathering off a Stratton roof and gets it back to a clean, even surface — either as a standalone tidy-up or as the first stage of a restoration. We treat the growth first so it dies at the root, then clean at a pressure matched to the tile so we lift the grime without stripping the surface or driving water under the laps.

Left alone, that growth holds moisture against the tiles and works into the pointing, which is why we treat rather than just blast it — the same method we use through nearby Midvale. We check the roof over while we’re up there and flag anything that needs attention, so a clean doesn’t paper over a repair that’s quietly getting worse. On steeper or two-storey Stratton roofs we work off proper anchorage and stay off the tiles where we can, so the clean lifts the grime without cracking the very surface it’s meant to protect, and we’ll let you know if the roof would be better served by a full restoration.

A roof restoration renews a tired but sound Stratton roof for a fraction of replacement: we treat the moss and lichen, high-pressure clean, replace broken tiles, re-bed and re-point the ridge caps in a flexible compound, then seal and coat with a Dulux AcraTex membrane as accredited applicators.

It’s the right call when the tiles have decades left but the surface and pointing are gone — the same judgement we bring to nearby Herne Hill. We’ll tell you honestly whether a restoration suits your roof or whether repairs or a re-roof make more sense, and the finished job carries both a manufacturer coating warranty and our 10-year workmanship warranty. Most Stratton homes take two to three days depending on the repairs needed before coating. As accredited applicators we prepare to the manufacturer’s specification, so the membrane actually holds — a coating only lasts if the surface beneath it was treated, cleaned and repaired properly first, which is exactly where a cheap spray-over fails within a couple of summers.

Most Stratton roof problems come down to a handful of failures: cracked or slipped tiles, perished ridge pointing, rusted valley irons and tired flashings. We trace the leak to its actual source — which is rarely under the ceiling stain — and fix the cause, whether that’s replacing matching tiles, re-bedding and re-pointing the ridge in a flexible compound, or renewing a corroded valley.

We’ll always tell you honestly when a roof is genuinely repairable versus when the repairs are mounting up and a restoration would serve you better, as it often does through nearby Red Hill. Prompt repair matters: a single cracked tile left through a wet winter becomes soaked insulation, stained ceilings and, eventually, damaged roof timber. Every repair is backed by our workmanship warranty, and because we photograph what we find and talk you through it, you’ll understand exactly what was wrong and what we did about it rather than being handed a bill and a shrug.

When a Stratton roof reaches the end of its life — porous tiles, rusted-through valleys, or a roof that’s been patched one too many times — a full re-roof is often the honest answer. We strip the old covering, check and repair the timber and battens underneath, and install a new tile or Colorbond roof with fresh sarking, valleys and flashings throughout.

A tile-to-Colorbond conversion is popular here for its lighter weight, clean lines and colour range, and because the lighter roof changes the wind uplift we reassess the tie-down as part of every conversion. We’ll also be straight about whether you’ve genuinely reached replacement or whether a restoration, as we do through nearby Koongamia, would renew the roof for a fraction of the cost. Every re-roof is engineered and tied down to Australian Standards and backed by our 10-year workmanship warranty, and we handle the guttering, flashings and tie-down as one job so nothing is left for you to chase afterwards.

A roof inspection is the cheapest way to know exactly what your Stratton roof needs before you commit to anything — or before you buy. We get onto the roof and into the roof space, physically checking the tiles, pointing, valleys, flashings, gutters and the structural timber, then hand back a clear written report with photographs.

On older homes we test the timber for rot, termite damage and delignification; on newer ones we look for the builder-grade detailing faults that leak early. It’s the same thorough check we run through nearby Millendon, and it’s what tells you whether a roof needs a minor repair, a restoration or something structural. If you’re buying a home, an inspection of the one part most people skip — the roof space — is money very well spent, and the written report gives you something concrete to put in front of an agent, a buyer or your insurer rather than a verbal all-clear.

Roof carpentry is the structural timber under your tiles — the rafters, battens and trusses that hold everything up. On Stratton homes we repair and rebuild that framing to standard: sistering weakened members, replacing rotted or termite-damaged timber, and reinstating trusses that have been cut for a skylight, duct or downlight.

We also test for delignification, the chemical breakdown that leaves roof timber looking sound but unable to hold a fixing — the same treatment we carry out through nearby Midvale where the timber is worth saving rather than replacing. As registered builders we can certify structural carpentry, which a general handyman can’t, and we assess the whole load path while we’re in the roof space so a repair addresses the cause, not just the symptom. Where a member is load-bearing we prop it safely with acrow props and work to a structural engineer’s design before anything is cut — it’s the natural companion to our tie-down and structural-defect work.